Flanges Market Demand Makes Room for New Growth Story
Jan 21, 2024Safety and health in the steel industry: Data report 2023
May 20, 2023Nuts And Bolts: Keeping It Tight
Aug 08, 2023Measuring Mass Flow Rate, Volume and Temperature with the FMC 5000 Coriolis Mass Flow Meter : Quote, RFQ, Price and Buy
Nov 06, 2023Denmark’s CNC Onsite to offer onsite wind turbine blade root repairs
Mar 29, 2023Converging orifice used to control the discharge rate of spherical particles from a flat floor silo | Scientific Reports
Scientific Reports volume 13, Article number: 669 (2023) Cite this article
1292 Accesses
5 Citations
Metrics details
The effect of the converging orifice geometry in a model silo on the discharge rate of monosized spherical particles was studied experimentally and numerically. The cylindrical container was equipped with interchangeable inserts with converging discharge orifices of various upper diameters in the upper base and a constant lower diameter in the lower base. Plastic PLA beads and agricultural granular materials: wheat, rapeseeds, and linseeds were tested. A series of discrete element method simulations corresponding to the performed experiments was conducted with a largely extended set of experimental discharge conditions. In the case of the constant thickness of the insert, the discharge rate initially increased with an increase in the half cone angle of the converging orifice and then the tendency reversed. In the majority of cases, the discharge rate through the converging orifice was higher than through the hopper with the same orifice diameter.
Questions of reliable flow of granular materials through horizontal orifices are the focus of interest in granular mechanics and technology. Despite the long standing investigations conducted by physicists and engineers, numerous effects remain obscure1. One of such effects is the influence of boundary conditions around the discharge gate on the flow pattern and the mass discharge rate (MDR) of granular material in a storage silo2,3,4. The MDR is one of the crucial parameters for the design and control of processes involving flow of granular materials and powders. A steady and precisely controlled flow rate is indispensable for preparing mixtures of materials in numerous branches. The boundary condition, i.e. the shape of the volume contained in the orifice and its vicinity, is a crucial factor determining the volume fraction and, consequently, the flow rate through the orifice1,5,6.
The flow rate through a horizontal orifice may be efficiently predicted by Beverloo’s equation7, which states that the mass discharge rate can be expressed as \(MDR = C\rho_{b} \sqrt g (d - kd_{p} )^{5/2}\), where d is the orifice diameter, dp is the particle diameter, g is the acceleration of gravity, ρb is the bulk density of discharging material, and C and k are the empirical discharge and shape coefficients, respectively. It has been revealed that the flow rate is different for small and large orifices (related to particle diameter), and the Beverloo relation breaks down for small orifices. Gella, Maza, & Zuriguel8 studied experimentally the effect of particle size on the mass flow rate from a model silo. The authors concluded that the relationship between the mass flow and the nature of contact interactions between particles, friction, or differences in kinetic energy per unit area is not trivial, and further research is necessary to clarify these questions. Beverloo, Leniger, & Van de Velde7 measured MDR during discharge of granular solids (mainly plant seeds) through an orifice in a flat bottom container. In such a configuration, stagnant material around the orifice forms a natural hopper where radial flow changes into a loose vertical stream of outflowing particles. A study on the effect of the cylindrical orifice geometry on the particle discharge rate was carried out for flat-bottomed silo by Zatloukal and Šklubalová9. Authors have confirmed a relationship between the discharge rate and the orifice size; however, they have also found a dependence of the flow rate on the orifice height. Zaki and Siraj10 have performed numerical simulations for three orifice shapes placed in the flat-bottomed cylindrical silo for spherical glass beads. Beverloo equation constants were calculated and the differences between the mass discharge rates for circular, triangular and square orifice were found. A high effect of the particle shape on the flow of particles discharged from the flat-bottomed silo has been reported by Hafez et al.11. Particle shape defines particle-to-particle interaction and relative mobility, which determine the discharge flow rate and the clogging behavior of granular solid.
In practical applications, silos with conical hoppers are frequently used, where no dead zone forms and discharging material slides along the smooth hopper surface. One of the first empirical equations predicting dependence of MDR on the conical hopper half cone angle α proposed by Rose & Tanaka12 is based on introduction into to the Beverloo equation the multiplicative factor comprising the impact of the half cone angle and the inclination of a stagnant zone boundary of the material inside the hopper. Saleh, Golshan, & Zarghami4 analyzed over twenty empirical models relating MDR to the hopper geometry. As concluded by the authors, no general rule has been established so far for the relationship between hopper half angle α and MDR.
Recently, reports have been published presenting numerical methods for designing hoppers with a varying contraction rate to maximize the mass discharge rate of granular material. The finite element method13,14 or the discrete element method15 with efficiency corroborated by experimental verification16 are used most often. Some results have shown that MDR can be increased by nearly 140% in a curved hopper, compared to a conical hopper with the same orifice size, hopper height, and silo diameter. Proper silo geometry may allow to control precisely the flow rate of granular material discharging the silo; however, understanding how to manipulate the mass discharge rate requires further research. That may have practical applications in metering, dosing or mixing.
Considering the results of above-mentioned studies, the objective of the reported project was to carry out a systematic study of the flow through a conical converging orifice with various values of thickness and half cone angle. A possibility of replacing the hopper bottom by the flat bottom equipped with converging discharge orifices in silo has been investigated. Motivation for the present study comes from the industrial flow of powders and grains in various devices. The converging parts, e.g. welding neck flanges, are common and important components of many practical apparatus used in the transport and processing of liquids and granular solids17,18.
So far no attempts have been made to use a numerical method for analyzing flow rate of granular materials through a conical converging orifice with various geometry. Therefore, series of the discrete element method simulations, supplemented by laboratory experiments have been performed. The specific appliance was designed for purpose of that project.
The experimental silo has been used to measure the mass discharge rate MDR. The cylindrical flat bottomed container (Fig. 1a) was 150 mm in diameter and 450 mm high. The container wall was made of galvanized steel, while its flat floor was made of plywood. Plastic PLA beads with a diameter of 5.95 mm, dp, and the mass of 0.25 g were used as reference particles. The number of PLA particles in the sample was equal to 14,000. Wheat, rapeseeds, and linseeds were tested as agricultural granular particles (Fig. 1b, Table 1). The frictional parameters of particles were determined with use of the tilting table method (Table 2). The silo diameter was 25 times bigger than the largest particle diameter, which, according to the findings reported in literature, allowed neglecting the influence of the bin wall19,20,21. A repeatable filling procedure was adopted to maintain a similar geometrical bedding structure in subsequent tests. A sieve was placed axially on the top surface of the silo. The measured amount of particles was poured through the sieve. After completion of filling, the top free surface was leveled. The discharge gate was opened and the mass of particles leaving the container was measured until the discharge was completed. Indications of three load cells supporting the silo were used to determine change in the mass of silo and particles during discharge. The change in the mass of discharged particles was determined also from indication of one load cell supporting the receiving container (not included into Fig. 1a). The mean value of outputs of this two measuring methods was used to calculate the discharge rate. The container was equipped with interchangeable 3D printed plastic inserts of various thickness, h. The converging orifice in the flat bottom of the model silo was defined by three parameters: the lower diameter, d0, the upper diameter, d1, and the insert thickness, h (i.e. the distance between the lower and the upper edge of the orifice). The converging orifices with the lower diameter d0 of 32.5 mm and various upper diameters d1 were selected to verify the key finding of the DEM simulations. The insert was placed in the cylindrical hole of the flat floor made of plywood and aligned with the top surface of the bottom (Fig. 1a). The insert with the upper diameter of the orifice d1 = 32.5 mm, the lower diameter d0 = 52.5 mm, and the thickness h = 6 mm served as the reference flat orifice (α = − 60º). Three replicate experiments were performed for each material.
(a) Scheme of the model bin with an interchangeable inset housing the converging orifice used for testing the mass discharge rate, and (b) PLA particles and seeds used for the experiments.
The DEM22 simulations have been performed with an assembly of 14,000 spherical particles with diameters randomly distributed in the range of 5.94–5.96 mm, with the mean, dp, of 5.95 mm, to reproduce the size of the PLA spherical particles applied in the experiments as the reference material. The numerical geometry mimicked the experimental setup. The thicknesses h of the inserts were tested in a range from 0 to 100 mm. The majority of them were normal multiplicities of the particle mean diameter. The lower diameter d0 ranged from 19 to 55 mm and the upper diameter d1 ranged from 32.5 to 72 mm, providing the half cone angle ranging between 4 and 90º. The reference lower diameter d0 of the orifice was 32.5 mm. The flat orifice with d1 = 32.5 mm (d0 > d1) served as a reference orifice providing a non-disturbed discharge. The discharge through conical hoppers with the same half cone angle as that of the converging orifice provided additional reference data of the mass discharge rate. The orifice diameter of the hopper was 32.5 mm and the upper diameter was 150 mm.
The Hertz-Mindlin no-slip contact model was applied for simulations following the Hertz theory23 as the default model used in the EDEM software package24. The material parameters of the particles were taken to reproduce the properties of the PLA particles: solid density ρ = 2212 kg/m3, Young’s modulus E = 8.8 GPa, and Poisson’s ratio ν = 0.2525. The frictional parameters between particles μp-p = 0.47, between particle and wall μp-w = 0.49, and between particle and bottom (plastic insert) μp-b = 0.21, as well as the coefficient of restitution e = 0.3 were determined experimentally. A default value of the rolling friction of 0.01 of EDEM software was applied for simulations. The walls of the silo were modelled with density ρ = 7800 kg/m3, Young’s modulus E = 200 GPa, and Poisson’s ratio ν = 0.25, which were material parameters of the steel.
Particles were generated inside the model silo. The particles were then discharged through a centrally located flat orifice, a converging orifice, or a conical hopper (Fig. 2). The simulations were performed with a time step of 1.6∙10–6 s with use of EDEM software package24.
Visualization of the contact forces between particles in the middle slice of model silo at rest: (a) flat orifice, (b) converging orifice, (c) hopper with the same α as that of the converging orifice.
The simulations were performed according to the following scheme of setting the converging orifice parameters:
(1) d1 = var., α = var., d0 = const., h = const.,
(2) d0 = var., d1 = d0 + const., h = const., α = const.,
(3) d0 = var., α = var., d1 = const., h = const.
The preliminary DEM simulations performed for the flat orifice (d0 > d1) with the diameter d1 in the range from 19 to 35 mm indicated that the threshold orifice size providing an undisturbed flow of material from the silo was 32.5 mm. Therefore, in the further study, the lower diameter d0 = 32.5 mm was applied for the simulations. The DEM simulated relationship between the mass discharge rate MDR and the upper diameter of the converging orifice d1 for d0 = 32.5 mm and several values of the insert thickness h are shown in Fig. 3a. The MDR calculated according to Beverloo’s equation with parameters C = 0.319 and k = 1.65 applied for the flat orifice was appended for comparison. For all thicknesses of the insert, the values of MDR initially followed Beverloo’s approximation until the maximum MDR was reached. The maxima of MDR and corresponding d1 increased with the increase in the insert thickness. They were located close to Beverloo’s approximation. Next, after surpassing the maximum, the MDR decreased initially rather fast and with growing d1 tending to a horizontal asymptote. The asymptotic value of the MDR for sufficiently high d1 (i.e. for α tending to 90º) is the MDR for the flat orifice of d1 = 32.5 mm.
(a) Mass discharge rate MDR influenced by the upper diameter of the orifice d1 for d0 = 32.5 mm and several values of the orifice thickness h. Discharge through the flat orifice approximated by Beverloo’s equation for C = 0.54 and k = 1.65, and (b) simulated MDRnorm. normalized by the mass discharge rate through the flat orifice with d1 = d0 = 32.5 mm as a function of the half cone angle α.
Figure 3b shows a change in the normalized mass discharge rate (MDRnorm.) with the increasing half cone angle α of the converging orifice. Mass discharge rates were normalized by the mass discharge rate determined for the flat orifice of d1 = 32.5 mm. For all tested thicknesses, the MDRnorm. initially increased with the increasing α. After the maximum was reached at αcrit., the mass flow rate monotonically declined to the MDR obtained for the flat reference orifice (i.e. MDRnorm. → 1). The highest maximum of the MDRnorm. (> 3) was obtained for αcrit. = 4º and h = 100 mm. The maximal values of MDRnorm. decreased with the decrease in the thickness of the insert and were noted for the higher half cone angle αcrit. For small values of αcrit. the maxima MDRnorm. obtained for the converging orifice were 5% lower than those obtained for the hopper with the same half cone angle α and the same orifice diameter of 32.5 mm, while the maxima for α > 20º were approximately 10% higher than those for the hopper.
The course of the relationships MDRnorm.(α) may be interpreted in the light of the Jenike criterion for the flow pattern in a conical hopper as dependent on the angle of internal friction and on the α value14,24. In the case of a steep hopper (low α), a mass flow takes place. After an increase in α to a limiting value, the flow pattern changes into a funnel flow. A further increase in α leads to formation of a stable dead zone with a converging flow identical to that present in a flat floor silo.
The results of the laboratory tests performed for four granular materials discharged from the converging orifice with geometry providing the maximum MDR in the DEM simulations were compared with the numerical results obtained for the same geometry of the converging orifice and for the hopper (Fig. 4). The experimental and numerical results were in reasonable agreement. Both of them showed the same tendency of a decrease in MDRnorm. with the αcrit. increase. Most of the experimental results were located very close to the results of the simulations performed for the converging orifice. The values of MDRnorm. for rapeseeds were lower than those for the other materials, which should be attributed to the over twice larger difference in the size of the seeds. This is consistent with the findings reported by Gella, Maza, & Zuriguel8, who indicated different profiles of the solid fraction in the vicinity of the orifice in assemblies of spheres of the same material and a four-fold difference in the diameter. The fairly close courses of the MDRnorm.(αcrit.) relationships for the hopper and for the converging orifice indicate a crucial role of the geometry of near proximity of the outlet for the flow rate of discharging material. Conditions on the hopper wall further from the outlet seem to have only a weak influence on the flow rate.
Comparison of the experimental and DEM simulated values of the normalized mass discharge rate MDRnorm. obtained for different alues of the critical half cone angle αcrit..
The analysis of the dependence of the MDR on α determined for d0 = 32.5 mm and for all the tested values of the parameters d1 and h has shown that the dependence of the critical value of the half cone angle on the orifice thickness αcrit.(h) separated the geometry of the converging orifice (h,α) into two regions with respect of the dependence of the MDR on α for d0 = const.: (1) the MDR increasing with α increase for α ≤ αcrit. and (2) the MDR decreasing with α increase for α > αcrit. (Fig. 5).
Relationship αcrit.(h) separating the geometry of the converging orifice (h,α) into two regions of increase (α < αcrit.) and decrease (α > αcrit.) of the mass discharge rate MDR with α increase determined for d0 = 32.5 mm.
Figure 6 presents the mass discharge rate MDR as the function of the upper diameter d1 of the converging orifice for two values of the insert thickness h and the half cone angle αcrit. providing the maximum discharge rate, compared with the results obtained for the flat orifice and Beverloo’s relationship. The critical value of the half cone angle αcrit. depended only on the insert thickness h. Contrary to the relationships shown by simulation scheme No. 1 (d0 = 32.5 mm, d1 = var.) (Fig. 4), the relationships obtained using scheme No. 2 (d1 = var., d1 = d0 + const., h = const., α = const.) followed Beverloo’s relationship very well. This means that the relationship MDR(d1) obtained for the converging orifice with α = const. ≤ αcrit. followed Beverloo’s relationship obtained for the flat orifice.
Comparison of simulated MDR(d1) relationships performed for the flat orifice and two values of the orifice thickness h of the converging orifice and the half cone angle αcrit. providing the maximum discharge rate with predictions of Beverloo’s equation.
The simulations performed according to the third scheme of setting the orifice parameters illustrate clearly the limits of the influence of the upper and the lower diameter of the converging orifice on the MDR. Figure 7a presents the MDR(d0) relationship and Fig. 7b shows the MDR(α) relationship, averaged over ten moments of time, for three different values of the thickness h and the upper diameter d1. In the case of h = 100 mm, the clear maximum MDR was observed for d0 = 32.5 mm followed by the plateau for d0 > 32.5 mm. For h = 12 and 6 mm, the dependence was more diffused and the plateau started at d0 a bit larger then 32.5 mm. For d1 = const., the MDR increased with d0 up to its maximum/plateau and remained almost constant with the further increase in d0 (Fig. 7a). Substituting the d0 variable with the corresponding half cone angle α under the condition d1 = const., it can be observed that the MDR remained almost constant for α ≤ αcrit. and decreased with the α increase for α > αcrit. (Fig. 7b). Scatter of the MDR illustrated in Fig. 7 as the standard deviation bars disturbed precise determination of α initiating the plateau. The difference in the course of dependencies presented in Figs. 3 and 7 results from applying the different independent x variable: d1 in Fig. 3a and d0 Fig. 7a. Additionally, the half cone angle α applied in Fig. 3b and Fig. 7b depends in different way on the variables d0 and d1 (\(\alpha = \tan^{ - 1} {{((d_{1} - d_{0} )} \mathord{\left/ {\vphantom {{((d_{1} - d_{0} )} {2h}}} \right. \kern-0pt} {2h}})\)). The MDR(α(d0)) relationship can be converted into the MDR(α(d1)) relationship applying superposition of relationships obtained according to the Discharge schemes No. 3 and No. 2.
Mass discharge rate MDR vs.: (a) the lower diameter of the orifice d0, (b) the half cone angle of the orifice α for three different values of the thickness h of the converging orifice and the upper diameter d1 providing maximum MDR for d0 = 32.5 mm.
Figure 8 shows changes in the mean porosity of the assembly of spherical particles determined in the volume of the orifice of d0 = 32.5 mm, for insert thickness of 100 mm (Fig. 8a), and 12 mm (Fig. 8b), at detention, after filling, and during commencement of the discharge. Porosity is defined as the ratio of the volume of pores to the volume of the assembly. The time variation of porosity in the volume of the orifice for several values of α has been shown. After filling, the porosity was approximately 48% in static conditions. For the insert with h = 100 mm, the discharge commencement produced a sharp increase in the porosity to a value dependent on α (Fig. 8a). For α values below 4°, the increase was nearly immediate. A further increase in α to 4° produced a substantial change in the p(t) relationship with a switch in porosity lasting for approximately 1.4 s. The porosity of the material flowing through the volume of the converging orifice was approximately 83% for α ≤ 4° and 53% for α ≥ 5°. The seemingly slight increase in α from 3° to 4° and subsequently to 5° produced substantial changes in the behavior of the material. The limiting value of the half cone angle was α = αcrit. = 4°. The porosity inside the corresponding volume of the hopper of the half cone angle α = 4° during the discharge was 53%, i.e. it was the same as the values of a dense flow obtained for the converging orifice with α > αcrit.. The same tendency for changes in the porosity was observed for the insert with h = 12 mm and αcrit. = 19.7º (Fig. 8b). In this case, the relationships were not as clear as for h = 100 mm due to relatively big scatter of data resulting from discrete nature of the process averaged over eight times lover volume.
Porosity of the granular assembly inside the volume of the orifice of d0 = 32.5 mm vs. time during filling, detention, and discharge for: (a) h = 100 mm, (b) h = 12 mm.
The comparison of the profiles of velocity Vz of particles during discharge for the flat orifice, converging orifice, and hopper with the same α and d0 (Fig. 9) explains the cause of the increase in the mass discharge rate through the converging orifice to values obtained for the hopper. For the converging orifice, at the level of the bottom edge of the orifice the particle velocity was approximately twice higher than the velocity of particles leaving the orifice (Fig. 9a). Figure 8a shows that the porosity in the converging orifice was also approximately twice higher than in the hopper. Therefore, the mass discharge rate, the product of the particle velocity and the bulk density, was similar for the converging orifice and the hopper with the same half cone angle α.
Profiles of the vertical velocity Vz averaged over ten moments of time, for the orifice of d0 = 32.5 mm: (a) in radial direction r at the level of the bottom edge of the orifice, (b) in vertical direction z (averaged over the cross-section of the orifice).
Profiles of the particles velocity Vz in the vertical direction have shown that the highest particles acceleration occurred in the converging orifice (Fig. 9b). Increase in the porosity during commencement of discharge through the converging orifice softened the structure of the bulk of particles, and, consequently, made accelerating particles easier due to gravity. Finally, it resulted in higher velocity at the level of the bottom edge of the orifice. Softening of the structure of the bulk of particles in the volume of the converging orifice with a thickness of a few particle diameters ensures the same mass discharge rate as the discharge of the dense structure of the bulk of particles through the hopper. This means that, by applying different geometries of the orifice, a similar mass discharge rate can be achieved by means of a stream of more densely packed particles with a lower particle velocity or a stream of more loosely packed particles with a higher particle velocity.
The need of deeper understanding of the kinematic transition region near the outlet in the silo is important for a precisely controlled discharge rate1,5. Therefore, the orifice dimensions were selected as variables to study discharge through the converging orifice.
The converging orifice can be considered as an extremely simplified curved hopper reduced into two segments: a flat floor and a short part of the hopper. Studies on the effect of the geometry of a conical converging orifice on the mass flow rate of granular material is scarce. Therefore, in this project, the results obtained for silos with conical hoppers were considered as a reference point. In the majority of cases, the flow rate through the converging orifice is higher than through the hopper with the same orifice diameter. Hence, the conical hopper may be replaced by flat bottom equipped with converging orifice with a smaller diameter to obtain the same discharge rate. The values of the MDR obtained for the converging orifice were located close to these provided by the hopper and considerably lower than the values provided by curved hopper, presented by Huang et al.16,26 and Guo et al.14.
The main novelty of the study is the indication of the hyperbolic type relationship between the half cone angle αcrit. and the thickness of the insert with converging orifice h separating the geometry of the converging orifice into two regions with respect of the dependence of the MDR on α for d0 = const.: (1) the MDR increasing with α increase for α ≤ αcrit. and (2) the MDR decreasing with α increase for α > αcrit.. The results of this study corroborated the observation that the flow mode (bulk density of the stream and particle velocity) of granular material through a conical converging orifice depends on the half cone angle of the orifice. For α < αcrit., the discharge commencement produces a rapid increase in the porosity of the material in the volume of the orifice associated with the higher particle velocity. Attaining α = αcrit. produced a substantial change. The increase in porosity with the discharge time was much slower and nearly linear. Slight surpassing αcrit. (by one or two degrees) allowed a denser flow with a lower particle velocity.
At the flat floor of the bin, a dead zone is formed generating a natural hopper. In this area, the flow direction changes from vertical to converging, which is associated with softening of structure of the material. In a hopper, the change in the direction of particle movement is much smoother, which results in much lower dilation and acceleration along the straight line of particle movement. Despite such a big difference in the characteristics of particle movement between the converging orifice and the hopper, the mass discharge rate may be similar for the same half cone angle and appropriately adjusted height of the converging orifice. As concluded by Gella, Maza, & Zuriguel8, it is difficult to definitively state which specific property of particles is responsible for the macroscopic changes observed in the system. The relationship among all these magnitudes is not trivial, and further research is necessary to clarify these questions. Understanding how to manipulate and control the mass discharge rate may have a positive impact on the productivity and quality of industrial unit operations.
The following detailed conclusions were drawn:
Material discharges in the dense (α > αcrit., porosity ≈ 60%) or loose (α ≤ αcrit., porosity ≈ 80%) flow mode depending on the insert thickness h and the angle of inclination of the generatrix of the converging orifice α. The maximal normalized mass discharge rate MDRnorm. decreased from 3.2 for h = 100 mm and α = 4º to 1.2 for h = 1.5 and α = 55º. In the majority of cases, the flow rate through the converging orifice is higher than through the hopper with the same orifice diameter.
For d0 = const. the critical value of the half cone angle αcrit. depended only on the insert thickness h. For α ≤ αcrit. the mass discharge rate followed Beverloo’s relationship obtained for the flat orifice. The hyperbolic type dependence of the critical value of the half cone angle αcrit. on the insert thickness separated the geometry of the converging orifice (h,α) into two regions of opposite reaction of the mass discharge rate MDR to α increase: (1) increase of the MDR with α increase for α < αcrit. and, (2) decrease of the MDR with α increase for α > αcrit..
The tendencies observed for the monodisperse assembly of spherical particles were preserved when beddings of wheat, lineseeds, and rapeseeds were tested. However, closer convergence of the results of the experiments and simulations would require fine tuning of the simulation parameters. The geometrical and mechanical parameters of real particles are far from those of a perfect sphere, which results in this discrepancy.
The results of the reported study show that the application of proper orifice geometry may allow precise control of the flow rate of granular material discharged from the silo. The fairly close compliance between the results of the experimental measurements and the simulations shows that DEM can be used to design equipment in systems involving granular flow.
All data generated or analyzed during this study are included in this published article. Further detailed information on the datasets elaborated during the current study is available from the corresponding author and can be provided on reasonable request.
Xiao, Y. et al. Experimental study of granular flow transition near the outlet in a flat-bottomed silo. Biosyst. Eng. 202, 16–27. https://doi.org/10.1016/j.biosystemseng.2020.11.013 (2021).
Article CAS Google Scholar
Murray, A. & Alonso-Marroquin, F. Increasing granular flow rate with obstructions. Pap. Phys. 8(1), 080003 (2016).
Article Google Scholar
Zheng, Q. J., Xia, B. S., Pan, R. H. & Yu, A. B. Prediction of mass discharge rate in conical hoppers using elastoplastic model. Powder Technol. 307, 63–72. https://doi.org/10.1016/j.powtec.2016.11.037 (2017).
Article CAS Google Scholar
Saleh, K., Golshan, S. & Zarghami, R. A review on gravity flow of free-flowing granular solids in silos—Basics and practical aspects. Chem. Eng. Sci. 192, 1011–1035. https://doi.org/10.1016/j.ces.2018.08.028 (2018).
Article CAS Google Scholar
Zuriguel, I. et al. Silo clogging reduction by a presence of an obstacle. Phys. Rev. Lett. 107, 278001. https://doi.org/10.1103/PhysRevLett.107.278001 (2011).
Article ADS CAS Google Scholar
López-Rodríguez, D. et al. Effect of hopper angle on granular clogging. Phys. Rev. E 99, 032901. https://doi.org/10.1103/PhysRevE.99.032901 (2019).
Article ADS Google Scholar
Beverloo, W. A., Leniger, H. A. & Van de Velde, J. The flow of granular solids through orifices. Chem. Eng. Sci. 15, 260–269. https://doi.org/10.1016/0009-2509(61)85030-6 (1961).
Article CAS Google Scholar
Gella, D., Maza, D. & Zuriguel, I. Role of particle size in the kinematic properties of silo flow. Phys. Rev. E 95, 052904. https://doi.org/10.1103/PhysRevE.95.052904 (2017).
Article ADS Google Scholar
Zatloukal, Z. & Šklubalová, Z. The effect of orifice geometry on particle discharge rate for a flat-bottomed cylindrical hopper. Part. Sci. Technol. 30, 316–328. https://doi.org/10.1080/02726351.2011.573839 (2012).
Article CAS Google Scholar
Zaki, M. & Siraj, M. S. Study of a flat-bottomed cylindrical silo with different orifice shapes. Powder Technol. 354, 641–652. https://doi.org/10.1016/j.powtec.2019.06.041 (2019).
Article CAS Google Scholar
Hafez, A. et al. The effect of particle shape on discharge and clogging. Sci. Rep. 11, 3309. https://doi.org/10.1038/s41598-021-82744-w (2021).
Article ADS CAS Google Scholar
Rose, H. F. & Tanaka, T. Rate of discharge of granular materials from bins and hoppers. Engineer 208, 465–469 (1959).
Google Scholar
Huang, Y. J., Nydal, O. J. & Yao, B. Time step criterions for nonlinear dense packed granular materials in time-driven method simulations. Powder Technol. 253, 80–88. https://doi.org/10.1016/j.powtec.2013.10.010 (2014).
Article CAS Google Scholar
Guo, Ch., Ya, M., Xu, Y. & Zheng, J. Comparison on discharge characteristics of conical and hyperbolic hoppers based on finite element method. Powder Technol. 394, 300–311. https://doi.org/10.1016/j.powtec.2021.08.064 (2021).
Article CAS Google Scholar
Liu, H. et al. Numerical analysis of the effect of the contraction rate of the curved hopper on flow characteristics of the silo discharge. Powder Technol. 356, 858–870. https://doi.org/10.1016/j.powtec.2019.09.033 (2019).
Article CAS Google Scholar
Huang, X., Zheng, Q., Yu, A. & Yan, W. Optimised curved hoppers with maximum mass discharge rate—An experimental study. Powder Technol. 377, 350–360. https://doi.org/10.1016/j.powtec.2020.08.084 (2021).
Article CAS Google Scholar
https://www.landeeflange.com/an-introduction-to-the-welding-neck-flange.html (2022).
Lumsden, S. & Black, I. American Petroleum Institute welding neck flange design for subsea pipelines. J. Process Mech. Eng. 224, 23–33. https://doi.org/10.1243/09544089JPME279 (2010).
Article Google Scholar
Nedderman, R. M., Tüzün, U., Savage, S. B. & Houlsby, G. T. The flow of granular materials—I: Discharge rates from hoppers. Chem. Eng. Sci. 37, 1597–1609. https://doi.org/10.1016/0009-2509(82)80029-8 (1982).
Article CAS Google Scholar
Hirshfeld, D., Radzyner, Y. & Rapaport, D. C. Molecular dynamics studies of granular flow through an aperture. Phys. Rev. E 56(4), 4404–4415. https://doi.org/10.1103/PhysRevE.56.4404 (1997).
Article ADS CAS Google Scholar
Zuriguel, I., Garcimartín, A., Maza, D., Pugnaloni, L. A. & Pastor, J. M. Jamming during the discharge of granular material from a silo. Phys. Rev. E 71(5), 051303. https://doi.org/10.1103/PhysRevE.71.051303 (2005).
Article ADS CAS Google Scholar
Cundall, P. A. & Strack, O. D. A discrete element model for granular assemblies. Géotechnique 29(1), 47–65 (1979).
Article Google Scholar
Timoshenko, S. P. & Goodier, J. N. Theory of elasticity (McGraw-Hill, 1970).
MATH Google Scholar
DEM Solutions Ltd. EDEM 2018.2 documentation. Copyright© 2018 (2018).
Horabik, J. et al. Determination of the restitution coefficient of seeds and coefficients of visco-elastic Hertz contact models for DEM simulations. Biosyst. Eng. 161, 106–119. https://doi.org/10.1016/j.biosystemseng.2017.06.009 (2017).
Article Google Scholar
Huang, X., Zheng, Q., Yu, A. & Yan, W. Shape optimization of conical hoppers to increase mass discharging rate. Powder Technol. 361, 179–189. https://doi.org/10.1016/j.powtec.2019.09.043 (2020).
Article CAS Google Scholar
Download references
Institute of Agrophysics, Polish Academy of Sciences, Doświadczalna 4, 20-290, Lublin, Poland
Joanna Wiącek, Józef Horabik, Marek Molenda, Piotr Parafiniuk, Maciej Bańda & Mateusz Stasiak
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
M.M., P.P. and M.B. developed and conducted the experiments. Numerical simulations were carried out by J.H. The results were analyzed by M.M, J.H. and J.W. The manuscript was written by J.H. and J.W. All authors discussed the results and commented on the manuscript.
Correspondence to Joanna Wiącek.
The authors declare no competing interests.
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
Reprints and permissions
Wiącek, J., Horabik, J., Molenda, M. et al. Converging orifice used to control the discharge rate of spherical particles from a flat floor silo. Sci Rep 13, 669 (2023). https://doi.org/10.1038/s41598-023-27431-8
Download citation
Received: 28 October 2022
Accepted: 02 January 2023
Published: 12 January 2023
DOI: https://doi.org/10.1038/s41598-023-27431-8
Anyone you share the following link with will be able to read this content:
Sorry, a shareable link is not currently available for this article.
Provided by the Springer Nature SharedIt content-sharing initiative